How To Install Tongue And Groove Wood Siding

Step 1: Gather Materials & Make a Plan

Using a crowbar and hammer carefully remove a section of your existing exterior cladding to see what is behind the onetime material. You are looking for an intact vapor barrier, plywood sheathing, and insulation. If none are present you lot will demand to buy this material when you pick upwards all your supplies to become started. Most lumber yards or big box stores will deliver right to your domicile for a minor fee for those who don't have a truck.

Next measure the width (a) and peak (b) of the walls y'all will be siding. Multiply those numbers together to get the square footage of your project (a x b= square footage). Next, decrease the square footage of any windows and doors on those walls from the overall foursquare footage of the projection. This will give you lot the square footage of siding you lot'll need when purchasing materials from your local lumber one thousand.

Footstep 2: Remove Existing Cladding

Using a crow bar and hammer proceed to remove the remaining material from the home.

Pace 3: Cheque Wall for Impairment

One time the one-time materials are removed you should run into a moisture barrier on pinnacle of the house sheathing (plywood). Remove the former moisture barrier due to the quondam nail holes and possible tears from the sometime siding textile. Supersede any damaged plywood or other type of sheathing as needed. If any plywood is removed, check the insulation backside this plywood and replace any that is damaged with new insulation.

Pace four: Install Moisture Barrier

One time you lot've replaced whatever insulation or damaged plywood sheathing, you need to install a new moisture barrier. Roll out the moisture bulwark or tar paper on the ground and cutting to length with your utility knife. Secure information technology to the plywood using 2" galvanized roofing nails. Make sure you beginning from the bottom of wall and work your way up and overlap the moisture barrier a couple inches each time. This will keep wind and h2o out of the wall cavities.

Pace 5: Cut Starter Plank

A starter plank must be cut to ensure a clean outward-facing border. To exercise this, mark one tongue and groove exterior plank to the necessary length and run it through the table saw with its groove facing the blade. One time the groove is cut from the plank, a smooth, clean border is created, resulting in a more finished look. PRO TIP- prime the backs of the planks to added another level of moisture protection.

Step 6: Install Starter Plank

Using a carpenter's pencil and a half-dozen' level, scribe a straight vertical line direct along the exterior surface where the outer edge of the starter plank will sit. Hold the starter plank upward to the level line and secure it into the plywood bankroll using a smash gun and stainless steel 2" nails.

Footstep 7: Cut & Attach Vertical Planks

Measure out, mark and cut each tongue and groove exterior plank to size based on the pitch of the roof and the bottom edge of the wall. Next, fit groove edges into tongue edges, securing into plywood backing and to ane another using a boom gun using stainless steel 2" stop nails. Being that you are nailing into the "blind" part of the natural language y'all will not see the boom head in one case the next lath is installed. It is highly recommended using a power nailer or stapler being that this is a soft wood and then it doesn't split during the nailing process. This also saves on time and gives you a much cleaner wait. PRO TIP- Miter cut the planks' bottoms to minimize water wicking upward into the boards and possibly into the firm.

Pace viii: Install Effectually Windows & Doors

As the vertical planks come into contact with doors and windows, cut each plank to size for a proper fit on top of required flashing. Continue installation from left to right, securing planks in place using the same method as above.

Step 9: Wrap Edges

For a make clean, finished look, miter the edges of boards that volition meet at the house's corners. Fit planks together and attach using the same method every bit with other planks.

Step 10: Add together Trim

Measure, mark and cut 1″x2″ wood trim to size using a tabular array saw. Next, place along the surface of the dwelling house's outside and secure in place with same stainless steel 2" nails and nail gun. To give a clean finished look you lot can fill the nail holes with wood filler before you apply your sealer.

Step 11: Caulk, Stain & Seal

Wipe surface of woods using damp cloth and let to dry. Next, caulk where the vertical planks meet the brick. So, apply stain and sealant using staining pad or rag.

One time yous've finished this natural language-and-groove outside, your firm volition be the envy of the neighborhood.

Add together architectural involvement to your dwelling'due south exterior with a vertical tongue and groove woods plank awarding.

We've compiled a full listing of materials y'all'll need to install exterior wood siding to your home hither:

Tongue and Groove Outside Woods Plank (nosotros suggest cedar, redwood, or pine)
Curlicue of Moisture Barrier
Table Saw
Miter Saw
Smash Gun
2″ Stainless Steel Exterior Cease Nails
eleven-Guess 2" Steel Roofing Nails
Outside Stain
Staining Pads
Damp Textile
Rag
Hammer
Crow Bar
Measuring Tape
6' Level
Carpenter'south Pencil
4'x8' Sheets of Pressure-Treated Plywood
Utility Knife
1″x2″ Wood Trim
Outside Caulk

Source: https://www.thinkwood.com/blog/how-to-install-exterior-wood-siding

Posted by: hayesalmot1972.blogspot.com